[sword-devel] osis2mod

Johan johan.marais at messianic.co.za
Sun Mar 11 10:43:21 MST 2018


Thank you David.

 

The DataPath in the conf is indeed with a forward slash, i.e. - DataPath=./modules/texts/ztext/ts2009/

 

Best regards,

 

Johan Marais

Institute for Scripture Research

 <http://www.messianic.co.za/> www.messianic.co.za 

 

From: David Haslam [mailto:dfhdfh at protonmail.com] 
Sent: Sunday, 11 March 2018 19:21
To: SWORD Developers' Collaboration Forum <sword-devel at crosswire.org>
Subject: Re: [sword-devel] osis2mod

 

Except in the .conf file, the module path in Windows should use rather than /

 

The .conf file is cross-platform, so a choice was made at the beginning to use / as in Linux. 

 

Best regards, David 

 

 

Sent from ProtonMail Mobile

  _____  

 

On Sun, Mar 11, 2018 at 16:47, DM Smith <dmsmith at crosswire.org <mailto:dmsmith at crosswire.org> > wrote:

Johan, 

 

The output should be located at ./modules/texts/ztext/ts2009. Those folders should already be there. There should be some kind of failure message if it cannot open the output files for writing. If there are currently files there it should update them. 

 

Since you didn’t include any flags for compression, the module that is put there won’t be compressed.

 

osis2mod doesn’t care about the module’s conf. That is supposed to be created based upon how you build the module, i.e. what flags you use for osis2mod. I’m guessing your conf doesn’t match with regard to compression. If that’s the case the module won’t work.

 

Also if you are on a modern version of Windows, you might not have permission to write to c:Program Files (x86)CrossWireThe SWORD Projectmodules extsztext s2009

 

Hope this helps,

DM Smith 

  _____  

 

On Mar 11, 2018, at 10:00 AM, Johan <johan.marais at messianic.co.za <mailto:johan.marais at messianic.co.za> > wrote:

 

DM Smith, 

  

It looks like this: 

  

C:Program Files (x86)CrossWireThe SWORD Project>osis2mod ./modules/texts/ztext/ts2009/ TS2009Ver100.osis.xml -c ts2009 

You are running osis2mod: $Rev: 3314 $ 

Adding cipher filter with phrase: ts2009 

SUCCESS: osis2mod: has finished its work and will now rest 

  

C:Program Files (x86)CrossWireThe SWORD Project> 

  

Only the following are in the "The SWORD Project" folder: 

Utilities from Xiphos 

TS2009Ver100.osis.xml file 

ts2009.conf file in the "mods.d" folder 

The following folder structure, under "The SWORD Project" 

modules 

   texts 

      ztext 

         ts2009 

  

The .conf file starts with [TS2009] and the  

DataPath=./modules/texts/ztext/ts2009/ 

  

Thank you, 

  

Johan 

From: DM Smith [ <mailto:dmsmith at crosswire.org> mailto:dmsmith at crosswire.org]  
Sent: Sunday, 11 March 2018 14:18 
To: SWORD Developers' Collaboration Forum < <mailto:sword-devel at crosswire.org> sword-devel at crosswire.org> 
Subject: Re: [sword-devel] osis2mod 

  

Johan, 

Please tell us your entire command line. We can then answer your question.  

— DM Smith 

  


On Mar 11, 2018, at 7:43 AM, Johan < <mailto:johan.marais at messianic.co.za> johan.marais at messianic.co.za> wrote: 

Good day, 

I created a bible module (osis.xml) which I want to convert into a Sword bible module, using osis2mod. 

It looks as if it works correctly, but there is no output. 

I receive this message: 

You are running osis2mod: $Rev: 3314 $ 

Adding cipher filter with phrase: xxxxxx 

SUCCESS: osis2mod: has finished its work and will now rest 

This is the message directly under the command line. 

What could be the problem please? 

Thanks for all the help. 

Johan 

_______________________________________________
sword-devel mailing list:  <mailto:sword-devel at crosswire.org> sword-devel at crosswire.org 
 <http://www.crosswire.org/mailman/listinfo/sword-devel> http://www.crosswire.org/mailman/listinfo/sword-devel 
Instructions to unsubscribe/change your settings at above page 

_______________________________________________ 
sword-devel mailing list:  <mailto:sword-devel at crosswire.org> sword-devel at crosswire.org 
 <http://www.crosswire.org/mailman/listinfo/sword-devel> http://www.crosswire.org/mailman/listinfo/sword-devel 
Instructions to unsubscribe/change your settings at above page 

 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.crosswire.org/pipermail/sword-devel/attachments/20180311/16ba832f/attachment.html>


More information about the sword-devel mailing list